Vegetables in greenhouses, greenhouses, etc. Due to their special environmental conditions, no matter which kind of vegetables are cultivated, the occurrence of pests and diseases is increasing. According to the production practice, the use of spray method to prevent and control the vegetable pests and diseases is time-consuming and labor-intensive, and increases the humidity of the greenhouse. The application of the dust method not only overcomes the drawbacks of the spray method to increase the humidity of the greenhouse, but also saves time and effort. The advantages of good control effect and so on. The technical points of the dust application are as follows:
First, the application of drugs and dosage. The applicator can be a Harvester-5 or a Harvest-10 handgun. It is required that the wind speed of the spout is above 8 m/s, the shaking speed of the harvesting type-5 hand crank should reach 36 rpm, and the harvest type-10 should reach 50 rpm, the purpose is to produce a strong enough powder. The wind causes the powder to be evenly discharged. The amount of powder discharged is adjusted to about 200 grams per minute. Generally, 1 kilogram of dust is used per acre, and the treatment time is 5 minutes.
Second, the best time to spray. The best time for dusting is morning or evening. The cockroach has not been uncovered or just closed, so the deposition rate of the powder on the crop is higher. Noon should be avoided at noon on sunny days, and powder can be sprayed at any time on cloudy days. Ventilation can be turned on after about 2 hours of dusting. The first spraying is in the early stage of the disease, and it is sprayed once every 7-10 days according to the condition. Pay attention to the vents and doors of the shed before the dusting. Close the plastic cloth of the shed and try to reach the sealed state. If the shed is only damaged, it will have no effect on the dust.
Third, the technical essentials of dusting. (1) Greenhouse: Using the horizontal spray method of retreat, that is, starting from the inner end of the greenhouse, the operator stands on the aisle, facing away from the north wall of the greenhouse, facing the south side, while spraying on the air, while retreating, until the door is exited, the door is closed. If there is any medicine, the powder spray pipe can be inserted into the room from the upper air outlet to spray, until the remaining powder is sprayed. (2) Greenhouse: It adopts the left and right air swing spraying method. From the north end, the operator stands on the aisle and swings the powder spray pipe to spray powder to the left and right sides. While spraying, it retreats until it exits the door of the southern end and closes the door. (3) Small and medium-sized arch shed: The shed-out spraying method is adopted, that is, a part of the shed is uncovered on one side or two sides of the shed, and the powder-spraying pipe is inserted into the shed to spray, and the nozzle swings left and right.
Fourth, the precautions for dusting. Dust method must pay attention to the powder spraying technique. When spraying, the nozzle should be facing upwards, and the powder should be sprayed evenly into the air in the booth. Do not spray the powder spray tube to the plant line by line, otherwise the landing will be uneven. At the same time, be sure to follow the pesticide safety operation procedures when operating, and wear long-sleeved overalls, wearing goggles, masks and protective caps. After the application, it is necessary to walk out of the shed in time, and then wash your face, wash your hands and rinse your mouth with clean water.
First, the application of drugs and dosage. The applicator can be a Harvester-5 or a Harvest-10 handgun. It is required that the wind speed of the spout is above 8 m/s, the shaking speed of the harvesting type-5 hand crank should reach 36 rpm, and the harvest type-10 should reach 50 rpm, the purpose is to produce a strong enough powder. The wind causes the powder to be evenly discharged. The amount of powder discharged is adjusted to about 200 grams per minute. Generally, 1 kilogram of dust is used per acre, and the treatment time is 5 minutes.
Second, the best time to spray. The best time for dusting is morning or evening. The cockroach has not been uncovered or just closed, so the deposition rate of the powder on the crop is higher. Noon should be avoided at noon on sunny days, and powder can be sprayed at any time on cloudy days. Ventilation can be turned on after about 2 hours of dusting. The first spraying is in the early stage of the disease, and it is sprayed once every 7-10 days according to the condition. Pay attention to the vents and doors of the shed before the dusting. Close the plastic cloth of the shed and try to reach the sealed state. If the shed is only damaged, it will have no effect on the dust.
Third, the technical essentials of dusting. (1) Greenhouse: Using the horizontal spray method of retreat, that is, starting from the inner end of the greenhouse, the operator stands on the aisle, facing away from the north wall of the greenhouse, facing the south side, while spraying on the air, while retreating, until the door is exited, the door is closed. If there is any medicine, the powder spray pipe can be inserted into the room from the upper air outlet to spray, until the remaining powder is sprayed. (2) Greenhouse: It adopts the left and right air swing spraying method. From the north end, the operator stands on the aisle and swings the powder spray pipe to spray powder to the left and right sides. While spraying, it retreats until it exits the door of the southern end and closes the door. (3) Small and medium-sized arch shed: The shed-out spraying method is adopted, that is, a part of the shed is uncovered on one side or two sides of the shed, and the powder-spraying pipe is inserted into the shed to spray, and the nozzle swings left and right.
Fourth, the precautions for dusting. Dust method must pay attention to the powder spraying technique. When spraying, the nozzle should be facing upwards, and the powder should be sprayed evenly into the air in the booth. Do not spray the powder spray tube to the plant line by line, otherwise the landing will be uneven. At the same time, be sure to follow the pesticide safety operation procedures when operating, and wear long-sleeved overalls, wearing goggles, masks and protective caps. After the application, it is necessary to walk out of the shed in time, and then wash your face, wash your hands and rinse your mouth with clean water.
ã€Comment】 ã€Print this article】 ã€Close this page】 ã€Large, medium and small】
CZL-YB-××-L series Load Cell is spoke type structure, and is produced by alloy steel. Its bearing form is compression type. It
has various features such as low height, convenient installation and operation, strong anti-overload capacity and small power consumption, and has the capacity from 1t to 50t. It uses inside glue sealing, has excellent damp proof and anti-corrosion proof performances, and can be used in adverse environment. It is suitable for explosive danger fields, and has product explosion-proof label Exia â…¡ CT6Ga; ExiaD20T85. It can be used for producing electronic scales such as electronic Truck Scale and Hopper Scale.
Industrial Load Cells,Strain Gauge Load Cell,Low Height Analogue Load Cell,Spoke Load Cell
SHANDONG JINZHONG SCIENCE & TECHNOLOGY GROUP COMPANY LIMITED , https://www.chinagoldbell.com