If you do not want to shower upstairs when it rains downstairs, then it is necessary to pay attention to bathroom waterproof and ensure quality. Someday you were bathing and suddenly the doorbell rang and hurriedly opened the door. At a glance, the downstairs household was glaring at you, and it was bad. Bathroom waterproofing has a lot of places to pay attention to, one of which is the height of the bathroom's waterproof, must meet the requirements, otherwise it is prone to seepage. Let's take a look at how the toilet waterproof height is required in the end.
Bathroom waterproof height: Be sure to do wall waterproofing. Before wall tiles, do wall waterproof. In the general waterproofing process, the wall surface is to be waterproofed to a height of 30 cm. However, for a non-load-bearing lightweight wall, the entire wall should be waterproofed, and at least 60 cm in height must be achieved.
Bathroom waterproof height, bathroom floor waterproof decoration height
The waterproofing of the bathroom floor is the most important part of our bathroom decoration, so the waterproof height of the ground must be refined. Bathroom floor waterproof height, usually we choose to use reinforced concrete floor pavement, 1:3 cement mortar to find the slope layer, the minimum thickness of the ground must also be 20mm thick, 30mm thick dry cement mortar combined layer, slope to floor drain, Once wiped.
Bathroom waterproof height II. Bathroom wall waterproof decoration height
For the height of the waterproof wall, a waterproof height of 30 cm is generally required. When the wall is not load-bearing, the waterproof height of the entire wall should be at least 1.8 meters. Wall waterproof paint to do about 30cm high, to prevent the accumulation of water infiltration wall surface dampness. The height of the bathroom wall of the shower room is generally 180cm; there is a bathtub, and the height of the wall adjacent to the bathtub should be 30cm higher than the height of the bathtub.
Bathroom waterproof height III. Bathroom floor tiles waterproof decoration height
The installation of floor tiles is an important part of our bathroom's waterproofing. In addition to laying a floor tile, we must make a waterproof layer under the surface. We should use cement mortar to level the floor and apply a waterproof coating. When the waterproof layer of the floor tile is in contact with the wall, it should be upward. From above, about 25~30cm above the ground. The height of the bathroom's sewer's waterproofing is related to our future health problems. Therefore, when handling it, one thing is to prevent the odor in the drainage pipe from overflowing into the interior of the sewer to prevent the sewer from plugging.
Waterproof height of bathroom IV . Waterproof decoration height of bathroom washbasin and urinal
The wall of the bathroom that is in contact with the washbasin is 300mm above the washbasin; if your toilet is not a toilet but a toilet bowl, then it has a waterproof height of 1800mm above the floor. The pipe (including the casing) that passes through the floor in the bathroom shall have a waterproof height of approximately 100 mm from the root of the pipe.
The content of how to measure the height of the bathroom's waterproofing is here. The bathroom is a place with lots of water. Therefore, it is very necessary to do certain waterproof measures. I hope to help you better handle the problems of bathroom leaks.
Bathroom waterproof decoration waterproof
The RFID Seal tags is one way lock, can open it one lock unless damage it.
Industrial level material, ABS or PPS, waterproof, high temperature resistance.
And pupular using in trees management, assesses management, water meter and pipeline management etc. Any hard working environment, it is a great option.
You logo or variable numbers would be laser printed on the rfid seal surface, making the management more easy.
RFID Seal Tag can be embedded 125Khz chips like Tk4100, EM4200, T5577, EME44305 and Hitag etc.
RFID Seal Tag can be embedded 13.56MHZ chips like Ntag213, NTAG215, NTAG216, Mifare Classic, Desfire EV2/EV2, Plus X, Plus SE, ICODE, Ultralight, TI 2084, Topaz512, and F08 etc.
RFID seal tag can be embedded 860MHZ-960MHZ chips like Alien H3, Alien H4, U-Code Gen2 and Impinj M4/M5 etc.
Besides, SunwayRFID also provides silicone rfid wristband, rifd bracelet, Elastic Wristband, snap wristband, Fabric Wristbands, pvc wristbands, RFID Keychain, RFID Tag and rfid cards too, one-shop can meet all your need about RFID.
Price, customer service, and quality always at our first place.
RFID Seal Tag
RFID Seal Tag,Seal Tag,RFID Seal,Plastic Seal Tag
Sunway Smartech Co.,LTD , https://www.sunwayrfid.com