Advantages of wall-hung boilers

The wall-hung boiler has a powerful home central heating function, and each room can freely set comfort temperature according to demand, and can provide large-flow constant-temperature sanitary hot water for home bathing, kitchen and other places. And its compact body, easy to use is also a modern expression of life and new home fashion highlights. In addition, today's wall-hung boilers have incorporated many advantages such as panel personalization, efficient energy use, more environmentally-friendly drainage, and multi-use heating hot water. What is the installation method of the boiler ? Where are the advantages of fireplaces, here to give you a detailed talk, I hope to help you!

Introduction to the advantages of boilers

1, saving energy and environmental protection to save costs

Households using wall-hung boilers avoid the problems of difficulty in adjustment and waste of energy in collective heating. According to the need for flexible adjustment of heating temperature, some gas boilers can be connected to the radiator and floor heating system, saving energy by 20% compared to most heating methods. When no one is at home, the indoor temperature setting can be turned down or turned off to save unnecessary heat loss.

2, easy and flexible control

Easy and flexible handling

Wall-hung boilers are radiant heat-dissipating systems, and their heat-dissipation points are found throughout the room. Users can flexibly adjust the temperature of the boiler, and can achieve partition temperature control, allowing users to freely set the room temperature and start and stop time. After closing the fireplace, the room will remain in a certain warmth for a long time.

3, heating comfort

The circulating heat of the boiler gas heating system adopts a bottom-up approach, which brings a warm feeling from the feet to the head. It is not as dry as the plumbing. Some brands also provide wall-hung boilers with physiotherapy functions. With far-infrared heat conduction, there is no feeling of dizziness or dryness even when staying in the room for a long time.

Wall-hung boiler installation method

First, prepare before installation

Prepare before installation

Before installing the wall-hung boiler, make sure that the installation position of the boiler and the fuel gas are the same. If it is inconsistent, replace it. If there are no holes for the flue and hanging stoves, first hit the flue and reserve enough pipe diameters. If the installation site is a non-heat-resistant wall, insulation protection should be used.

Second, install the template and hook

In the purchase of the wall-hung boiler enclosure, an installation formwork bracket is included. Drill holes in the wall and fix it to the wall with fixing bolts. Note that at least 10 mm is reserved for the gap on both sides. Then bolts and hooks provided in the fixed installation of the template. Then, install the gas valve, install the exhaust valve at the highest point of the system, and install the fill valve and drain valve at the lowest point.

Third, install the boiler

Installation of boiler

Take out the boiler body, remove the knob, remove the cover, and install the device on the wall hook. Then start to install the flue, connect the bottom of the five pipes, pay attention to add gaskets, tighten. Finally, connect the power supply and indoor temperature controller. Open the front panel of the machine and connect the power supply according to N, L, and E. Connect the 1-3 contacts according to the requirements of the temperature controller, and then attach the cover.

Four, water injection leak detection

Water leak detection

Water injection and leak detection is one of the most important steps in the boiler installation. Open the water inlet switch and water injection switch, fill the heating system with water, increase the pressure to 3, close the water injection switch to see if there is a leak, and pay attention to whether the safety valve is unloaded Pressure. At the same time open the hot faucet in the bathroom to see if there is a leak. Test the gas line with soapy water for gas leaks. If there is no problem, open the drain valve and lower the pressure to 1 to complete. Everything is normal and the whole installation process is completed reasonably.

Summary: The information about the advantages of wall-hung boilers and boiler installation methods was introduced here. I hope this article will be helpful to everyone. If you still have something you don't understand, you can leave a message to Xiaobian at the bottom. We will answer your questions as soon as possible.

Wall-hung boiler

solder ring bronze fittings produced as kembla and connex,the lead of the solder is much lower than them,Solder Ring Bronze Fittings, pre-solder bronze fittings ,yorkshire solder ring fittings, connex solder ring fittings ,solder ring gunmetal fittings,solder ring Bronze Fittings ,pre-solder bronze fittings ,yorkshire solder ring fittings,connex solder ring fittings,solder ring gunmetal fittings

Solder Ring Bronze Fittings

solder ring bronze fittings,pre-solder bronze fittings,yorkshire solder ring fittings,connex solder ring fittings,solder ring gunmetal fittings

Taizhou Runde Company , https://www.smartfittings.com